Tekno RC EB48

[KingClod27]

Hey guys gonna start my Tekno Buggy thread soon and wanted to put it in the right section...

Im going to try to do a step by step build with lots of pics and maybe vid too if I get up the courage lol...

Ive been on rctech.net researching and asking questions about the build process and electronics and setups...Great guys over there too (for the most part lol)...learned alot in the past week.

If you guys have any advice PLEASE chime in during the build..I value all of your opinions!

 

[william g]

me personally I like to run a really really thick lube in the center diff because I bash more than race.

 

[JoeWorks]

Nice. Contrats on the win.

My offroad racing friends and I use a a smart phone app called "RC Setups". It was around 3 bucks.

You can download setup sheets from the pro drivers on various tracks world wide on almost all onroad and offroad chassis and vairous scales for free.

I just downloaded all my Losi and Kyosho setsheets thats available, look for track conditions closest to my local track and based my chassis setup on it. We also share setups via email. who knows your local track may be listed.

its basicly the ones you can download from the chassis manufacurers in hard copy format but you can duplicate it as much as you want and input your own data. And its allways with you as long as you have your phone..LOL

Good luck and have fun.

Aloha

 

[KingClod27]

me personally I like to run a really really thick lube in the center diff because I bash more than race.

Cool...I think they gave me a few different weights fo oils so I think I will run a thicker lube because I will be bashing more at first...We have a few "run what you bring" classes at the track so Ill race it in there for now.

Nice. Contrats on the win.

My offroad racing friends and I use a a smart phone app called "RC Setups". It was around 3 bucks.

You can download setup sheets from the pro drivers on various tracks world wide on almost all onroad and offroad chassis and vairous scales for free.

I just downloaded all my Losi and Kyosho setsheets thats available, look for track conditions closest to my local track and based my chassis setup on it. We also share setups via email. who knows your local track may be listed.

its basicly the ones you can download from the chassis manufacurers in hard copy format but you can duplicate it as much as you want and input your own data. And its allways with you as long as you have your phone..LOL

Good luck and have fun.

Aloha

Thanks Joe...Ill look that up right now...a few guys on rctech.net gave me a few set ups too



Just finished reading the directions ...for the 10th time lol... Gonna give it a stab tonight and see how the build goes!

 

[KingClod27]

Ok....finally started on the Buggy tonite while I was watching football.

Started with the Center Diff Bag "A"

The updated directions stated I did not need the 4 shims on the spider gears for all 3 Diff gears. So tossed those to the side and gathered everything from Bag "A"....

Assemble the diff up to the spider gear step and added the oil (#7000) up to the top of the gears.

Completely assembled...

 

[Mo']

I have heard from a few sources that it's wise to build the diffs on the tight side an re-shim them after they break in. That was on the original kits though. Not sure if it has been updated yet but its definitely something to keep an eye on.

 

[KingClod27]

Next up was Bag "B"

Bag B is the front and rear Diffs....both built the same way but with different weight oils..The front Diff used #5000 oil and the rear used #3000 oil..

Started with greasing the output shafts again...

Then I built up the Diff halves and added the oil to the spider gears....

Here is the Front, Center and Rear Differential completely assmebled...

 

[KingClod27]

Bag "C"...Front Gear box

This part was actually very easy...Started out with greasing the front Diff, Then added the bearings, shims and bevel gear to the gearbox. Checked the gear mesh and and seems perfect, no grinding or binding...

Note*...The directions state if binding occurs to remove shims from gear side and put on opposite side.

Then I assembled the Gearbox and Shock tower....once again very easy step, but important to make sure the gears are meshed proper...

 

[KingClod27]

Bag "D" Rear gearbox...

The Rear Gearbox is build the same as the front except the shock tower is mounted different to allow the rear body post and wing mount to be installed....

Started out the same way by greasing the Diff, adding the bearings, shims and bevel gear to the gearbox.. Mesh seemed perfect again..no trouble..

Then I added the shock tower (only 2 screws this time), and the rear body post.

Note*.. the wing mount will screw into the back of the shock tower and then to the gearbox just like the front gearbox.

 

[TXT-2.0]

great start so far Gavyn ! looks like the instructions are well layed out and explain stuff well

 

[KingClod27]

great start so far Gavyn ! looks like the instructions are well layed out and explain stuff well

Thanks Tom...yes the directions are layed out very well so far and the parts are very high quality. Hoping I will get even more done tonite.

 

[KingClod27]

Bag "E"...Wing Mount

This step was actually time consuming lol....Had to assemble the Wing Mount and choose the position the wing be mounted..

I chose the stock postition for right now but might change to extreme downforce...All I have to do is change out the small tabs...

After that I attached the wing mount to the rear gearbox...It attaches in 4 places and is nice and secure...

You can actually see here how the locking nut fits into the wing mount for added protection and strength...

Finished product...

 

[KingClod27]

Bag "F"... Rear Suspension

Ok starting to move along a little quicker now.... started with the arms and installed the link for the sway bar setup, then the rear arm mud guards..

Next were the hingle pin plates...ver cool setup. The little taps allow you to adjust the setup of the hinge pins...Then connected the rear arms. Once again left everything in the stock position..

Part 2 of Bag "F" was the swaybar setup...

I really like how the sway bars are setup..They connect to the short link I installed on the rear arms and are secured on the rear of the gearbox.

 

[KingClod27]

Next up Bag "G"...Rear Hub Assembly

Installing the Rear hub and driveshafts was fun and fairly easy...I put the bearings in the hub and assembled the stub axles onto the driveshafts...then attached the wheel hubs..

Then I attached the hubs to the arms with hinge pins...

Part 2 of Bag G was installing the Camber Links..I think I made this part a little harder than it needed to be....had to take a food break and energize my brain lol..Once I got to this step on the front gearbox it was a little smoother lol..Started out by putting the pivot balls on the rod ends..the attached them to the rear hub and shock tower..

 

[KingClod27]

Next up Bag "H" Front Suspension...

The front suspension is pretty much the same process as the rear suspension so I wont go into too many details...I was able to assemble it quicker after learning from my mistake with the rear setup..Attached the arms and those heavy duty hinge pin plates. Then moved onto the sway bar setup again...

 

[william g]

moving along pretty quickly, methinks somebody is itching to pull the trigger

 

[KingClod27]

Next up Bag "I"...Front steering/hub Assembly..

Once again the front steering/hub assembly is basically the same as the rear except it adds steering....I wont go into too much detail here either, but just like in Bag H, I learned alot from the rear and it made the front come together alot easier...First I installed the bearings and top hats to the hub carrier and steering knuckle and attached them to the front arms...

Part 2 of Bag "I"...front camber links

And here are the finished (sorta) front and rear setups....Initial thoughts of the kit are very well laid out and easy to follow...Great support too...More to come soon!

 

[KingClod27]

So far so good with the Tekno EB48 Kit...I love how easy the directions are to follow and Tekno support is great...I can see why alot of people are raving about this Buggy, It has alot of adjustiblitly too. I will be able to toy with thousands of setups through out the Buggy...

My Original plan for Electronics was to go with a Tekin T8 RX8 system and 4s Lipo, Unfortunately with the holidays coming up I wont have the money to go with Tekin...right now. So I have decided to use SCT electronics and run it on a 2s Lipo. If Santa thinks Ive been a good boy I might have a Castle Mamba Monster under the tree (they are on sale this week on their site for Black Friday)...Also gonna go with a Savox servo for steering. I run Savox servos in all of my MTs and they are great...Probably will go with a 1256 or 1258. Gens Ace Lipos have worked out great for me too so I will grab 1 or 2 more from hobbypartz.com

I picked up a set of cheap "generic" wheels and tires so I could have a rolling chassis and something to bash with and not have to worry about ruining good race tires lol. I did find a few sets of tires I liked on VP Pro Racing.

So I hope by Thanksgiving I will have a rolling chassis and then I can anxiously wait for electronics lol....Thanks for checking out the thread and more to come soon!

 

[TXT-2.0]

what we have to wait till Thanksgiving !!!!!!why is it NOT a roller yet :emot15:





























kidding looks great so far Gavyn :emot112:

 

[im2tall]

Im just drooling right now !! Honestly just put a 1/8th scale system in there ,wait it out as long as you can ! It'll be worth it !! I was gonna suggest the HobbyWing ones they're actually not bad ,but they cost the same as the Castle systems on sale right now !!