Members do not see advertisements
Thanks Thanks:  0
Dislikes Dislikes:  0
Results 1 to 11 of 11
  1. #1

    Default KhyzerSoze's GMADE GOM GR01 Build

    Members do not see advertisements
    So... finally getting around to my GMADE GOM GR01 build. Just started today, and I'll post up progress as I go along.

    Build Details:
    GMADE GOM GR01 Rock Buggy Kit
    GMADE GOM Sway bar set (Titanium gray) GM30115
    GMADE GR01 Aluminum rear shock brace (Titanium gray) GM30080
    GMADE GR01 Aluminum slipper plate GM30073
    GMADE GA60 Brass steering knuckle bushing (4) GM30076
    GMADE GR01 Aluminum trailing arm (Titanium gray) GM30107
    Vanquish 25T Aluminum Servo Horn (on eBay)

    Brushed - Traxxas Titan 21T
    Brushless - SkyRC Ares Pro 540 Modified 8.5T (4100Kv), or Holmes Hobbies PULLER PRO BL 540 STANDARD (3500kv)

    Hobbywing WP-1080 Brushed ESC Or Castle Creations Mamba X
    FlySky R6B 2.4GHz 6-Channel Receiver
    FlySky GT-3C 2.4 GHz Radio
    Savox SC-1283SG Servo - (for steering)
    Savox SC-0254MG Servo - (for shifting)

    Tools / Materials:
    Versachem Brake Caliper Grease
    45 in 1 Precision Screwdriver Set
    Hakko FX-888D Soldering Station
    Tamiya Side Cutter
    DEWALT DCF610S2R 12V MAX Cordless Lithium-Ion 1/4 in. Hex Chuck Screwdriver Kit
    MIP Metric Speed Tip Set MIP9512
    Noleen SF3 Grease (on eBay)

    Last edited by khyzersoze; 18 Hours Ago at 01:54 PM.

  2. #2


    I forgot to take some photos during the beginning steps, but I'll remember going forward.

    Steps 1-13: Front and Rear Axles

    GMADE GA60 Brass steering knuckle bushing (4) GM30076

  3. #3


    Used Versachem Brake Caliper Grease to grease the gears.

    Steps 14-18: Transfer Case

  4. #4


    Used Versachem Brake Caliper Grease to grease the gears.

    Also added the GR01 Aluminum slipper plate (GM30073).

    Temporarily using a SkyRC Ares Pro 540 Competition 8.5T (4100kv) brushless motor for now. If I use this, I'll be using the Castle Mamba Monster X Esc.

    If I go the brushed route, I'll probably use the Hobbywing 1080 Esc + Maybe the Traxxas Titan 21T.

    Steps 19-27: Transmission

  5. #5


    Steps 28-37: Links

    Bought the upgraded trailing arms

    Comparison of stock trailing arms with the upgraded ones

    Links attached to skid

  6. #6


    Steps 38-45: Lower Chassis Part 1

    Transfer case, shift servo (Savox SC-0254mg), and transmission attached to skid. Using a SkyRC Ares Pro 8.5T (4100kv) brushless motor for now.

    Shift servo calibration using the 3ch 3position switch on the FlySky GT3C

  7. #7


    Steps 46-54: Lower Chassis Part 2 - Lower and upper front cage, battery tray, driver's side chassis rail.

  8. #8


    Steps 55-60 - Drive Shafts, Attaching Axles to chassis.

  9. #9


    Step 47: Steering Servo

    I skipped this step earlier, because I'm using the Savox SC-1283SG Servo.
    The kit comes with pre-molded servo spacers that encase the servo ears. They are pre-molded to fit most servos that use thinner plastic servo ears.
    The Savox 1283 is metal cased, and has thicker servo ears so the pre-molded servo spacer didn't fit.

    What I ended up doing was to use Yeah Racing M3 3mm spacers to space the servo up.

  10. #10


    Steps 61-68: Shocks

    I really need to get some more specific tools to do some of these build steps like the shocks. I'm sure I can do a much better job, but for now I'll keep winging it and improvising with the tools I have.

    Applying some Noleen grease (found on eBay) (thanks Jato!)

    Bought the upgraded metal rear shock brace for the GOM

    Last edited by khyzersoze; 18 Hours Ago at 01:54 PM.

  11. #11


    Members do not see advertisements
    Steps 69-74: Steering & Panhard Links/Rods

    So, I did run into a snag here. The panhard axle mount that the panhard rod attaches to on the axle uses a countersunk screw to secure it into place. The "eye" of that mount for that countersunk screw isn't very sturdy.

    Well... like someone from another forum that did the same thing that I didn't really remember until I did it myself.... I overtightened it by hand and "split" goes the eye of the panhard mount. Grrrr .

    It will hold for now as the other half of the eye is not broken.

    Anyway, I ordered the sprue that contains that particular part for now, while I wait for the upgrade metal part to show in stock at vendors. The panhard axle mount metal upgrade is one part that I WILL BE DOING.


Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts